Skip to content

Field guide

Arc Flash Calculator: IEEE 1584-2018 Incident Energy

Reviewed November 20, 2026 Standards-linked editorial Review policy

Free tool · no sign-in

Calculate incident energy and boundary

Enter the panel data. You get the numeric result and a watermarked label preview for free. The method covers 208 V to 15 kV; clearing time above 2,000 ms is refused rather than shortened.

Calculation support for qualified electrical-safety workflows. Not an engineered study, not a PE seal, not a work authorization. Method, limits and validation.

The form above is a working arc flash calculator. You enter panel data, the engine applies the IEEE 1584-2018 incident-energy method, and you get incident energy at the working distance, the arc-flash boundary, both arcing currents and the flags that say how far to trust the result. There is no sign-in and nothing to install. The longer version of the same tool, with fault-current and clearing-time assistants and a panel library, is at /calculator; this page is the one to read first if you want to know what the numbers mean.

Last reviewed: November 20, 2026.

What an arc flash calculation actually produces

An arc-flash risk assessment answers two questions about a piece of energized equipment: how much thermal energy would reach a worker at the working distance if an arc occurred, and how far away that energy drops to a level that cannot cause a second-degree burn. The first answer is incident energy, in calories per square centimetre. The second is the arc-flash boundary, the distance at which incident energy falls to 1.2 cal/cm². The definitions are written out on the incident energy and arc-flash boundary pages. The inputs that move both answers are few:

  • System voltage and available bolted fault current. They set the arcing current, which is lower than the bolted fault because an arc has impedance.
  • Electrode configuration. IEEE 1584-2018 defines five: VCB, VCBB, HCB, VOA and HOA. They describe how the conductors are arranged and whether the arc sits in a box or in open air.
  • Conductor gap and working distance. Gap shapes the arc; working distance is where the person stands, and energy falls off with distance.
  • Clearing time. How long the upstream protective device takes to open at the arcing current. Energy scales with time.
  • Enclosure size, when the box dimensions are known and differ from the typical box assumed by default.

Worked numbers from the engine

Take a 480 V panel, 25 kA available bolted fault current, VCB configuration, 32 mm gap, 455 mm (18 in) working distance and 200 ms clearing time at both arcing currents. The engine returns an arcing current of 18.34 kA, a reduced arcing current of 16.08 kA, incident energy of 9.5 cal/cm² and an arc-flash boundary of 65.5 in. Changing one input at a time, with everything else held:

Change from the base case Incident energy Arc-flash boundary
Base case 9.5 cal/cm² 65.5 in
Clearing time 100 ms 4.8 cal/cm² 42.4 in
Clearing time 500 ms 23.8 cal/cm² 116.2 in
Electrode configuration VCBB 13.2 cal/cm² 67.6 in
Electrode configuration HCB 19.5 cal/cm² 70.8 in
Available fault current 10 kA 3.6 cal/cm² 35.9 in
Working distance 610 mm (24 in) 6.0 cal/cm² 65.5 in

Three things are worth reading out of that table. Incident energy is proportional to clearing time here, so halving the time halves the energy; that is why maintenance-mode trip settings exist. The electrode configuration changes the answer by a large factor on identical electrical data, so picking the configuration that matches the real conductor arrangement is not a formality. And the boundary does not move when only the working distance changes, because the boundary is defined by the 1.2 cal/cm² point, not by where the worker stands. Every figure in the table is computed by the same engine that powers the form above, and the site's tests recompute them.

How the 2018 method differs from the 2002 edition

If you learned arc flash from the 2002 edition of IEEE 1584, or from a spreadsheet built on it, the 2018 edition changes several things that affect your numbers:

  • Five electrode configurations replace the old open-air and box split. The 2018 model distinguishes vertical and horizontal electrodes, with and without a barrier or box.
  • Two arcing currents are evaluated. The reduced arcing current covers the case where the arc current is low enough that the protective device is slower, and the worse result governs.
  • Enclosure size correction is explicit. The model takes the enclosure dimensions and corrects for them.
  • Grounding class is no longer an input. The 2002 edition had grounded and ungrounded cases. The tool still records the grounding for the label, but it does not change the 2018 values.
  • The model range is stated. 208 V to 15 kV for the calculated method. This tool refuses to extrapolate outside it.

Because the standard is copyrighted, this page describes behaviour and does not reproduce coefficients or equations. Buy the standard from IEEE if you need to audit the model itself. The methodology page lists what the engine is checked against.

Where this calculator stops

  • Calculated results cover 208 V to 15 kV, and the form rejects clearing times above 2,000 ms.
  • Outside the model window the tool falls back to the NFPA 70E table method only where a verified table row exists. The result then carries a PPE category and the label says TABLE METHOD. If nothing applies it says an engineering study is required and shows no number.
  • A calculated result is not converted to a PPE category. You select an arc-rated clothing system with a rating at least equal to the incident energy, and a qualified person documents the full system. The PPE category method page explains why the two methods are never mixed on one piece of equipment.
  • It models a single source feeding one piece of equipment. It does not model DC, single-phase, multiple sources, tie breakers or large motor contribution.
  • It cannot check the inputs. A bad clearing time gives a precise-looking wrong answer, so the form asks you to confirm each clearing time came from protective-device data.

An output from this page is an estimate for a qualified person to review. It does not replace an engineered arc-flash study, equipment-condition assessment, training, or an energized-work decision. OSHA's electrical-hazard guidance treats arc flash as a recognised hazard that employers must address, and NFPA 70E is the consensus standard it points to for the risk-assessment method.

From the number to a label and a permit

After you run the form you see a watermarked label render for free. A clean PDF, calculation record and energized-work permit are the paid step; the details are on the arc flash label maker page. If you only need the boundary and not a label, the arc flash boundary calculator shows the result on one page with nothing stored.

Getting the inputs right

Most wrong answers come from the inputs rather than the model. Available fault current is best taken from the utility or a short-circuit study; an estimate from transformer nameplate data is an upper bound that can mislead, as explained on what is available fault current. Clearing time comes from the time-current curve or trip-unit settings of the device upstream of the equipment. If you cannot read the curve, the clearing-time wizard walks you through a defensible choice and records where the value came from. Review the assessment at least every five years and after any change to the system, as NFPA 70E requires.

Direct answers

Frequently asked questions

Is this arc flash calculator free?

The calculation, the incident energy and boundary result, and a watermarked label preview are free and need no sign-in. The clean PDF bundle is a separate paid step, and its current status is shown beside the form.

Which standard does the calculator use?

IEEE 1584-2018 for the calculated method, covering 208 V to 15 kV. Where inputs fall outside that window it uses the NFPA 70E table method only where a verified table row exists, and otherwise states that an engineering study is required and shows no number.

Does it give me a PPE category?

Not for a calculated result. It reports incident energy and a minimum arc rating equal to it. A PPE category appears only when the NFPA 70E table method is the method used, and the two methods are never mixed on one piece of equipment.

Why does clearing time change the answer so much?

Incident energy scales with how long the arc persists. In the worked example on this page, 100 ms gives 4.8 cal/cm², 200 ms gives 9.5 cal/cm² and 500 ms gives 23.8 cal/cm², with everything else unchanged.

Can I rely on the result without an engineer?

It is calculation support for a qualified person. It cannot verify your fault current or clearing time, models one source feeding one piece of equipment, and does not replace an engineered arc-flash study.

How is this page different from /calculator?

/calculator is the fuller version of the same tool with assistants and a panel library. This page carries the explanation and a compact form that feeds the same engine. Search engines are pointed at this page as the canonical one for the tool.

Source trail

Sources

Standards references identify the applicable document or section where possible. Standards text may require licensed access. Report a factual issue through the process on our corrections page.