Skip to content

Field guide

Arc Flash Boundary Calculator: Distance to 1.2 cal/cm²

Reviewed November 20, 2026 Standards-linked editorial Review policy

Free tool · no sign-in

Find the arc-flash boundary

Runs the same IEEE 1584-2018 engine as the main calculator and shows the result on this page. Nothing is saved. The method covers 208 V to 15 kV; clearing time above 2,000 ms is refused rather than shortened.

Calculation support for qualified electrical-safety workflows. Not an engineered study, not a PE seal, not a work authorization. Method, limits and validation.

The boundary calculator above returns one headline number, the arc-flash boundary: the distance from a potential arc source at which incident energy has fallen to 1.2 cal/cm². It runs the same IEEE 1584-2018 engine as the main calculator, shows the result on this page, and stores nothing. Submitting the form changes the address bar, so you can bookmark a case or send it to a colleague for checking.

Last reviewed: November 20, 2026.

What the boundary means in practice

Inside the boundary, an unprotected person could suffer a second-degree burn if an arc occurred. Outside it, the thermal energy has thinned out below that threshold. The 1.2 cal/cm² level comes from the skin-burn research the electrical-safety standards are built on, and the arc-flash boundary page explains it along with how it differs from the shock approach boundaries, which protect against a different hazard and are set by voltage, not by arc energy. For planning a task, the boundary tells you where to put barricades and who must be inside the arc-flash risk assessment and wearing arc-rated protection.

The boundary is a thermal line only. It does not describe pressure, flying debris, or toxic fume, and it does not make the space outside it safe to ignore.

What you need to enter

The form asks for the same nine values as the main calculator, because the boundary depends on the incident-energy model:

  • System voltage, line-to-line, 208 V to 15 kV for a calculated result.
  • Available bolted fault current in kA, from the utility or a short-circuit study.
  • Electrode configuration, one of VCB, VCBB, HCB, VOA or HOA.
  • Conductor gap in millimetres. The form defaults to 32 mm; 25 mm is typical of LV panelboards and motor control centres.
  • Working distance. It does not change the boundary but it sets the incident-energy figure shown beside it.
  • Clearing time at the arcing current and at the reduced arcing current, in milliseconds, from the protective device.

Two confirmation boxes ask you to attest that the clearing times came from protective-device data. They are required because the clearing time moves the answer more than any other input you control, and a time typed from memory is the usual source of a wrong boundary.

How each input moves the boundary

Starting from a 480 V panel with 25 kA available bolted fault current, VCB configuration, 32 mm gap, 455 mm working distance and 200 ms clearing time, the engine returns a boundary of 65.5 in, about 5 ft 5 in, with 9.5 cal/cm² at the working distance. Changing one thing at a time:

Change from the base case Arc-flash boundary Incident energy at 455 mm
Base case 65.5 in 9.5 cal/cm²
Clearing time 100 ms 42.4 in 4.8 cal/cm²
Clearing time 500 ms 116.2 in 23.8 cal/cm²
Electrode configuration VCBB 67.6 in 13.2 cal/cm²
Electrode configuration HCB 70.8 in 19.5 cal/cm²
Available fault current 10 kA 35.9 in 3.6 cal/cm²
Working distance 610 mm 65.5 in 6.0 cal/cm²
Clearing time 200 ms at Iarc, 400 ms at Iarc_min 93.4 in 16.8 cal/cm²

The last row is the one that surprises people. When the device is slower at the reduced arcing current, that case governs and both the energy and the boundary jump, even though the full-current numbers are unchanged. The calculator reports the governing case and says so in a flag. The engine computes every figure above, and the site's automated tests recompute them from the engine and compare them with this page.

The boundary grows with time, but not in proportion. Doubling the clearing time from 100 ms to 200 ms moves it from 42.4 in to 65.5 in, because energy falls off with distance rather than linearly. Cutting the time is still the cheapest way to shrink the boundary, which is why maintenance-mode trip settings and faster protective devices are standard energy-reduction measures.

Why a lower fault current can mean a larger boundary

It sounds backwards, and it only happens when clearing time changes with the current. In the table above the 10 kA case has a smaller boundary than the 25 kA case because the clearing time is held at 200 ms in both. Real protective devices do not behave that way. A lower available fault current produces a lower arcing current, and an inverse-time device trips more slowly at lower current. If the time goes up faster than the current comes down, the energy and the boundary go up. This is the reason the form asks for the clearing time at the reduced arcing current separately, and why an estimate of fault current from transformer nameplate data can understate the hazard. The available fault current page covers it in full.

Reading the result

When the method is calculated, the result block shows the boundary in inches, feet and inches, and millimetres, the incident energy at the working distance, and both arcing currents. It also lists flags. If the boundary is farther out than the working distance, which is the normal case on a live panel, a flag says that the person at the working distance is inside it. Select an arc-rated clothing system with a rating at least equal to the incident energy; the result is not converted into a PPE category. The what cal suit do I need page maps a rating to the typical clothing system.

When the inputs fall outside the IEEE 1584-2018 window the tool uses the NFPA 70E table method if a verified row exists, and says so. The boundary then comes from the table and carries a PPE category. If neither method applies, it reports that an engineering study is required and shows no boundary.

Where this calculator stops

  • The calculated method covers 208 V to 15 kV. Clearing times above 2,000 ms are refused instead of shortened.
  • Working distances under 305 mm are raised to 305 mm, and the result says so.
  • It models one source feeding one piece of equipment. DC systems, single-phase systems, multiple sources, tie breakers and large motor contribution are outside it.
  • It cannot verify the inputs. The boundary is only as good as the fault current and clearing time you supply.
  • The boundary describes thermal exposure from an arc event. It is not a shock approach boundary, and it does not define who is a qualified person.

IEEE 1584 and NFPA 70E are copyrighted. This page cites them and describes how the method behaves without reproducing equations, coefficients or table values.

The output is an estimate to be reviewed by a qualified person, who must confirm the clearing times against the real device settings. It does not replace an engineered arc-flash study.

From a boundary to a label

The boundary is one of the fields NFPA 70E expects on the field-applied label, alongside nominal voltage and either incident energy or a PPE level. The button under a result sends the same inputs to the arc flash label maker, where you get a watermarked preview for free. The broader arc flash calculator page explains the method and its differences from the 2002 edition. Review the assessment behind any label at least every five years and after changes to the system.

Direct answers

Frequently asked questions

What is the arc-flash boundary?

The distance from a potential arc source at which incident energy falls to 1.2 cal/cm². Inside it an unprotected person could receive a second-degree burn.

Does working distance change the boundary?

No. The boundary is defined by the 1.2 cal/cm² point. Working distance changes the incident energy shown beside it, not the boundary distance.

Why can a lower fault current give a larger boundary?

A lower fault current lowers the arcing current, and an inverse-time protective device can trip more slowly at the lower current. If the clearing time rises faster than the current falls, energy and boundary rise.

Is the boundary the same as the shock approach boundary?

No. The arc-flash boundary is a thermal distance computed from the arc. The shock boundaries protect against electric shock and are set by voltage.

Does the tool save my inputs?

No. The boundary calculator shows the engine result on the page and stores nothing. The optional label button sends the inputs to the label maker, which does store a record.

Source trail

Sources

Standards references identify the applicable document or section where possible. Standards text may require licensed access. Report a factual issue through the process on our corrections page.